Garage Door Spring Conversion Calculator

Measure the torsion spring (or springs) on your door now. Get replacements that lift the same door: one spring to two, two to one, another wire size or inside diameter, or a longer life.

1. Your springs now

Your spring

How to
How to
How to

Wound coils only, cones not included. Measure a relaxed (unwound or broken) spring: a wound one measures long.

2. Your door
How to
ft
in
How to
ft
in

Used only to check the new springs fit on the shaft.

How to
3. Your new springs
Rate this calculator

How garage door spring conversion works

A torsion spring does one job: it twists the shaft hard enough to hold the door's weight. That twist is the spring's torque. Any set of springs that puts the same torque on the shaft at the same number of turns balances the same door, whatever their size and however many there are.

So a conversion has three steps, and the calculator does all three:

  1. Work out the IPPT (inch-pounds per turn) of the spring or springs on the door now, from wire size, inside diameter and length.
  2. Multiply by the turns your door needs (from its height, track radius and drum) to get the total torque, and the weight it balances.
  3. For every stocked wire size, solve the length that gives the new spring count the same torque, then estimate how many cycles each one lasts.

Example: one spring to two

A 7 ft door on a 15" radius track and 4" drums has one .250 x 2 x 32 spring. At 7.94 turns it has an IPPT of 36.88, lifts 146.4 lbs and is good for about 15,000 cycles. Converting to two springs on a 2" inside diameter gives, among others:

  • 2 x .207 x 2 x 25.5: lifts 145.7 lbs, about 33,000 cycles
  • 2 x .218 x 2 x 32.5: lifts 147.4 lbs, about 63,000 cycles

Each spring of a pair carries half the load, so it is under far less stress. That is why going from one spring to two usually adds a lot of life for very little extra cost, and the door does not drop if one spring breaks.

Example: a longer-life pair

The same door with two .225 x 2 x 25 springs lifts 223.7 lbs, at about 13,000 cycles. Keeping two springs but moving up in wire size:

  • 2 x .234 x 2 x 30.5: lifts 222.2 lbs, about 23,000 cycles
  • 2 x .243 x 2 x 36.5: lifts 223.3 lbs, about 37,000 cycles

Thicker wire needs a longer spring to carry the same weight, and the longer spring lasts longer. Check that the longer set still fits on your shaft: the calculator flags any set that is too long for the door width you enter.

What to measure

  • Wire size: measure 20 coils tight together and divide by 20.
  • Inside diameter: usually stamped on the winding cone, most often 1.75" or 2".
  • Length: the wound coils only, not the cones, on a relaxed spring. A wound spring measures long.
  • Door height and track radius: they set the number of turns.

Not sure your old springs were ever right? Start from the door instead: the spring size calculator by door weight sizes springs from what the door actually weighs. To check a single spring, use the garage door spring calculator.

Torsion springs hold enough energy to cause serious injury. This calculator tells you what to buy; unwinding, winding and installing springs takes proper winding bars and training. If in doubt, call a garage door technician.

Frequently Asked Questions

Can I replace one garage door spring with two?

Yes, and it is a common upgrade. Each spring of the pair carries half the load, so the pair usually lasts much longer than the single spring it replaces, and the door stays put if one spring breaks. A pair is one left-wound and one right-wound spring, one on each side of the centre bracket. Set the old spring as 1 spring and the new springs to 2 in the calculator.

Can I replace two springs with one?

Only on a light door. One spring has to carry the whole door, so it needs much heavier wire and lasts far fewer cycles. Set the new springs to 1 and the calculator shows whether any stocked wire size does it at the life you ask for; on heavier doors none will.

Can I use a different wire size than my old spring?

Yes, as long as the length changes with it. A thicker wire needs a longer spring to give the same lift, and lasts longer. A thinner wire needs a shorter spring and lasts less. The calculator solves the right length for every stocked wire size.

What is IPPT on a garage door spring?

IPPT means inch-pounds per turn: how much torque a spring adds for each turn you wind into it. It depends on the wire size, the inside diameter and the length. Two springs with the same IPPT, wound the same number of turns, lift the same weight. For a set of springs, add their IPPT together.

Can I change from a 1.75 inch to a 2 inch inside diameter?

Yes. With the same wire size, a spring with a bigger inside diameter is softer, so it has to be shorter to lift the same weight. Choose the new inside diameter under "Your new springs" and the lengths are solved for it.

My two springs are different sizes. What should I buy?

Tick "My two springs are different sizes" and enter both. The calculator adds them together and gives you a matched pair that carries the same total. If the door never balanced well, the old springs may have been wrong in the first place: weigh the door and use the spring size calculator by door weight instead.

Why is the new lift a few pounds different from my old springs?

Springs are sold in half-inch lengths, so the exact length is rounded to the nearest half inch. That moves the lift by a few pounds either way, which is normal and is taken up when the springs are wound.